Siemens S7 Instrukcja Użytkownika Strona 83
- Strona / 222
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
83
SIMATIC NET NCM S7 for Industrial Ethernet
C79000-G8976-C129–06
Configuring Communication Connections
This chapter explains the following:
S The general aspects of configuring communication connections
S How to configure ISO transport connections, ISO-on-TCP and TCP connections
S How to use the connection configuration functions to specify communication
partners that exchange data via UDP
You will find a description of the connection-specific properties dialogs in the
following sections:
S ISO transport connections see Section 4.4
S ISO-on-TCP connections see Section 4.5
S TCP connections see Section 4.6
S UDP see Section 4.7
You will find further information in the following sources:
S For the properties of the configurable connection types, refer to Section 1.5.
S For the properties of the configurable connection type E-mail, refer to /5/.
S You will find information on the numbers of connections and amounts of data in
Section 3.1.
S For information on configuring connections, refer to the online help of STEP 7
by selecting Help
"
Contents.
4
- Audience 6
- Scope of this Manual 6
- Symbols used in this Manual 6
- Conventions 9
- Contents 10
- Stations 13
- 1.1 Industrial Ethernet 14
- Configuration and Diagnostics 18
- Industrial Ethernet 22
- Configuring S7 Connections 25
- Interface 27
- IP (Internet Protocol) 28
- SEND/RECEIVE interface 28
- Connection Types 30
- SIMATIC S5 30
- Configuring 31
- Networking in a Multiproject 31
- Variants 32
- Configuration of the System 33
- (Sub)Project 36
- Projects 39
- (TCP/IP) 41
- Ethernet Option 44
- 2.2 Procedure 45
- Procedure 46
- Subnet Attachment 49
- Graphic Overview in NetPro 52
- Overview in Table Form 53
- Options Tab 55
- S Assigning an IP address 56
- S Ethernet Profile for 56
- S Resetting module memory 56
- S Send Keepalives for 57
- S Multiplex OP Connections / 58
- Diagnostics Tab 59
- Addressing Tab 59
- Setting Up Connections 63
- Latest CPs) 64
- Requirements 65
- Alternative Procedure 67
- Principle 69
- Type of Interface 69
- Functions (FCs) 74
- Amounts of Data 74
- Purpose of the FCs 75
- Programming Connections 75
- 3.4 Additional Information 80
- Known Problems 81
- 4.1 Procedure 84
- 4.3 Connections 87
- Tasks of the Ethernet CP 88
- New Connection 90
- Unspecified Connections 94
- 4.3.3 Further Functions 96
- Display (Example) 98
- General Tab 100
- C79000-G8976-C129–06 101
- Address Parameters 102
- Addresses Tab 103
- TSAP Format 103
- Local and Remote TSAPs 103
- Default TSAPs 104
- Dynamics Tab 105
- Attributes AccessDescription 106
- Modifiable 106
- Display only 106
- Figure 4-11 107
- System Memory 108
- Links to Other Systems 108
- Overview Tab 109
- Introduction 110
- Opening the Dialog 110
- Address parameter 113
- Figure 4-16 116
- Figure 4-20 124
- Figure 4-21 125
- Application 134
- Figure 4-27 137
- 4.7.5 Free UDP Connection 139
- Routing to Distribute Load 140
- S7 Ethernet CPs 141
- Block Library 142
- Evaluating Status Codes 147
- Overview 148
- Working with the Job Header 151
- Meaning of the Block 152
- How the Block Works 153
- S Note the block type: 156
- S Note on the S7-400: 156
- Condition Codes 156
- DONE MeaningSTATUSERROR 158
- Example of AG_SEND 159
- NDR MeaningSTATUSERROR 166
- Caution when Configuring 167
- 5.4.1 FC7 AG_LOCK 169
- 5.4.2 FC8 AG_UNLOCK 171
- NCM S7 Diagnostics 175
- 6.1 Overview 176
- Functions 177
- Mode-Dependent Functions 177
- Installation 178
- Structure 179
- Operation 179
- 6.2.2 General Menu Commands 180
- S Dialog update time 181
- S Show TSAP in ASCII 181
- Ethernet CP 182
- Internetworking 183
- Other Startup Options 184
- 6.4 How to Use Diagnostics 185
- Firmware Loader 191
- 7.1 Application 192
- 7.2 Loading Firmware 193
- 2nd Step 194
- 3rd Step 194
- References 197
- Order Numbers 200
- Glossary 201
- B.1 General Section 202
- B.2 Industrial Ethernet 206
- B.3 PROFInet 208
- Linking to Other Systems with 211
- FETCH/WRITE 211
- “Parameter Values“ 212
- Parameter Values 214
- PI/PQ C T 215
- Document History 217
- A&D Technical Support 221
Powiązane produkty i podręczniki dla Oprogramowanie Siemens S7
Oprogramowanie Siemens Gigaset C675 IP Dokumentacja
(187 strony)
(187 strony)
Oprogramowanie Siemens COM32 Podręcznik Użytkownika
(126 strony)
(126 strony)
Oprogramowanie Siemens SIMATIC NET Dokumentacja
(268 strony)
(268 strony)
Oprogramowanie Siemens v1.0 Instrukcja Obsługi
(202 strony)
(202 strony)
Oprogramowanie Siemens S7-400 Instrukcja Obsługi
(382 strony)
(382 strony)
Oprogramowanie Siemens AC65 Podręcznik Użytkownika
(123 strony)
(123 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji