Siemens NAN 67 Series Instrukcja Użytkownika Pobierz pdf (Strona 43)

Appendix B: CRC-16 Calculation

02/13 Modbus® RTU Serial Communications User Manual 37

Address

(hex)

(decimal)

Parameter Name Access Notes

013A 40315 Auto/Manual State R/W Bit Packed

Bit 0: 0:Manual; 1:Auto

Bit 1-15: Unused Note 12

013B 40316 Set Point State R/W Unsigned 16 bit integer

0=SP1 2=SP3

1=SP2 3=SP4 Note 12

013C 40317 Remote/Local Set Point State R/W Bit Packed

Bit 0: 0:LSP; 1:RSP

Bit 1-15: Unused Note 12

013D 40318 Tune Set State R/W Unsigned 16 bit integer

0=Tune Set #1 1=Tune Set #2

2=Tune Set #3 3=Tune Set #4

013E 40319 Loop Status R Bit Packed

Bit 0: Mode: 0:Manual; 1:Auto

Bit 1: Set Point: 0:SP1; 1:SP2

Bit 2: Remote/Local: 0:LSP; 1:RSP

Bit 3: Tune Set: 0:Set #1; 1:Set #2

Bit 4: LSP3

Bit 5: LSP4

Bit 6: CSP

Bit 7: UDC3500 set for Tune Set #1

Bit 8: UDC3500 set for Tune Set #3

Bit 9: UDC3500 set for Tune Set #4

Bit 10: Unused

Bit 11: UDC3500 Run/Hold Status

Bit 12: UDC3500 set for Any Digital Input

Active

Bit 13: UDC3500 set for Any Alarm Active

Bit 14: UDC3500 set for Cascade

Bit 15: UDC3500 set for Guaranteed Soak

Deviation (Out of Limit)

Note 10, Note 12

Note 1 :UDC3200, UDC3300, UDC3500 uses a prescale of 100 for this parameter.

Note 2: UDC3200, UDC3300, UDC3500 uses a prescale of 1 for this parameter.

Note 3: UDC3200, UDC3300, UDC3500 only.

Note 4:

UDC3200, UDC3300, UDC3500 Ratio and Bias are CSP parameters.

Note 5: In the UDC3500, if the input type is configured as Carbon and the input algorithm is configured for one of the carbon

selections, the prescale value is derived from the configured decimal point.

Note 6: Not supported by UDC2300 or UDC3300

Note 7: UDC2300, UDC2500, UDC3300, UDC3200 Loop 1 Address only.

Note 8:

In the UDC3200, UDC3300, or UDC3500, if the Algorithm 1 type is configured for weighted average, RH, Summer, Sq.

Root Mult-Div, Sq Root Mult, Mult-Div, Mult, Carbon A-D, FCC, Dew Point, or Oxygen, the prescale value is derived

from the configured decimal point.

Note 9: In the UDC3300, or UDC3500 if the Algorithm 2 type is configured for weighted average, A-B/C, Sq Root Mult-Div, Sq

Root Mult, Mult-Div, Mult, or Dew Point, the prescale value is derived from the configured decimal point.

Note 10: If bits 2, 4, 5 and 6 are set, then disregard bit 1.

Note 11: UDC3500: Positional Proportional Control slidewire input or Three Position Step Control slidewire feedback

Note 12: UDC2300, UDC2500,

UDC3200, UDC3300, UDC3500 only.

1 2 ... 38 39 40 41 42 43 44 45 46 47 48 ... 75 76

Komentarze do niniejszej Instrukcji

Brak uwag

Siemens NAN 67 Series Instrukcja Użytkownika Strona 43

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Płyty grzewcze Siemens NAN 67 Series