Siemens SPCK421 Dokumentacja Strona 168
- Strona / 296
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
15
Engineer programming via the browser
Configuring zones, doors and areas
168
Siemens AB
A6V10276959
Security Products
18.11.2011
15.8.2.1 Entry/Exit
Configure the following Entry/Exit settings:
Entry time
The time (in seconds) allowed for unsetting to be completed. The entry
time applies to all entry/exit zones in that area (default: 45 seconds)
See Timers [➙ 160].
Exit time
The time (in seconds) allowed for a user to leave a protected area
before setting is complete. The exit time applies to all entry/exit zones in
that area (default: 45 seconds) See Timers [➙ 160].
Disable Exit Time
Select if no exit timer is required and setting is activated by ‘Exit term’
zone or ‘Entry exit’ zone with ‘Final exit’ attribute. See Timers [➙ 160].
Fob Unset Entry
FOB will only unset when entry timer is running. Default is enabled.
15.8.2.2 Partset Options
Configure the operation of particular zones for both Partset A and Partset B modes
as detailed below:
Partset Enable
Enable PartSet for A and B operation as required.
Partset Timed:
Tick the relevant checkbox (Partset A or B) to apply the exit
timer to the Partset A or B mode.
Partset Access:
Tick the relevant checkbox to change access zones into
entry/exit type zones for either Partset A or B operation. This
feature is useful for a domestic installation where a Passive
Infrared (PIR) sensor is located in the hallway. If the user
partsets the system at night and returns downstairs during the
night, he/she may unintentionally activate the PIR sensor in
the hallway and trigger the alarm. By setting the partset
- Siemens AB 1
- Copyright 2
- Table of contents 3
- 1 Meaning of symbols 10
- 2 Security 11
- 2.2.2 Transport 12
- 2.2.3 Setup 12
- 2.2.4 Operation 12
- Security 14
- Meaning of hazard symbols 14
- 3 Directives and standards 15
- 4 Technical Data 19
- Technical Data 20
- SPC4000 20
- 4.2 SPC5000 21
- 4.3 SPC6000 23
- 5 Introduction 26
- 6 Mounting system equipment 27
- Standard enclosure 28
- 6.2 Mounting a G3 enclosure 29
- Back Tamper Requirements 30
- Mounting system equipment 31
- Mounting a G3 enclosure 31
- 6.3 Battery installation 34
- 6.4 Mounting a keypad 35
- 6.5 Mounting an expander 35
- 7 Controller hardware 36
- Controller hardware 37
- 8 Door Controller 39
- 9 Wiring the system 40
- 9.1.1 Loop configuration 41
- 9.1.2 Spur configuration 42
- Spur configuration 43
- Star configuration 44
- Multi-drop configuration 44
- Star wiring 46
- Multi-drop wiring 46
- Mixed wiring 47
- 9.1.4 Shielding 48
- 9.1.5 Cable Map 49
- Wiring of a branch expander 50
- Standard wiring 51
- Wiring the system 52
- Wiring the zone inputs 52
- External bell wiring 54
- Plug-in modules 55
- Powering from battery only 56
- 11 Keypad user interface 57
- Keypad user interface 58
- SPCK420/421 58
- Keypad display 59
- Entering numeric values 61
- Entering text 61
- 11.2 SPCK620/623 62
- 11.2.2 LED description 64
- Emergency Keys 66
- Direct Settings 66
- SPCK620/623 67
- 12 Starting the system 68
- 12.2.1 Fast Programmer 69
- 12.4 Creating system users 70
- Receiver area on the keypad 71
- Starting the system 72
- 14.1 SYSTEM STATUS 75
- 14.2 OPTIONS 76
- 14.3 TIMERS 79
- 14.4 AREAS 81
- 14.5 X-BUS 82
- 14.5.2 RECONFIGURE 83
- 14.5.3.1 LOCATE 84
- 14.5.3.2 MONITOR 84
- 14.5.3.3 EDIT KEYPADS 85
- Comfort Keypad Settings 86
- 14.5.3.4 EDIT EXPANDERS 88
- 14.5.4 ADRESSING MODE 90
- 14.5.5 XBUS TYPE 90
- 14.6 WIRELESS 91
- 14.6.1 ADD SENSORS 92
- 14.6.3 ADD WPA 93
- 14.6.4 EDIT WPA 93
- 14.7 ZONES 94
- 14.8 DOORS 94
- Door inputs 95
- Door Groups 95
- 14.9 OUTPUTS 98
- 14.10 COMMUNICATION 101
- 14.10.2 ETHERNET PORTS 102
- 14.10.3 MODEMS 102
- 14.10.4 CENTRAL STATION 103
- 14.10.4.1 ADD 103
- 14.11 TEST 104
- 14.11.3 ZONE MONITOR 105
- 14.11.2 WALK TEST 105
- 14.11.4 OUTPUT TEST 106
- 14.11.5 SOAK TEST 106
- 14.11.6 AUDIBLE OPTIONS 107
- 14.11.7 WPA TEST 107
- 14.11.8 SEISMIC TEST 107
- 14.12 UTILITIES 108
- 14.13 ISOLATE 108
- 14.14 EVENT LOG 109
- 14.15 CHANGE PIN 109
- 14.16 USERS 109
- 14.16.2 EDIT 110
- 14.16.2.1 ACCESS CONTROL 110
- CARD FORMAT 111
- Card attributes 112
- Supported card formats 112
- 14.17 ENGINEER SMS 113
- 14.18 X-10 114
- 14.19 SET DATE/TIME 114
- 14.20 INSTALLER TEXT 115
- 14.21 DOOR CONTROL 115
- 15.1 Ethernet interface 116
- Connect the cable 117
- 15.2 USB interface 118
- Logging into the browser 119
- 15.4 Panel status 120
- 15.4.2 Zones 121
- Performable actions 122
- 15.4.3 Doors 123
- 15.4.4 System alerts 124
- 15.4.5 Areas 125
- 15.4.6 Wireless 125
- 15.4.7 X-Bus 127
- 15.4.8 Logs 128
- 15.4.8.1 System Log 128
- 15.4.8.2 Access Log 128
- 15.5 Users 129
- 15.5.2 User rights 131
- 15.5.3 Access control 134
- 15.5.6 Engineer SMS 138
- 15.6 File Operations 140
- 15.6.1 Upgrading Firmware 141
- Controller Firmware Upgrade 142
- Peripheral Firmware Upgrade 143
- File Operations 144
- SPC controller interface 145
- PC USB interface 145
- For Windows XP and 2000 146
- For Windows Vista 146
- KeypadReleased 148
- 15.6.3.3.1 148
- BrowserReleased 149
- 15.6.3.3.2 149
- 15.7.1 Identification 150
- 15.7.2 Standards 151
- Changing system settings 152
- 15.7.2.1 Installation type 153
- 15.7.2.2 Region 153
- 15.7.2.3 Grade 153
- 15.7.3 Options 154
- System Options 156
- 15.7.4 Timers 160
- 15.7.5 Clock 164
- 15.7.6 Language 164
- 15.8.1 Editing a zone 165
- Domestic 167
- Commercial 167
- Financial 167
- 15.8.2.1 Entry/Exit 168
- 15.8.2.2 Partset Options 168
- 15.8.2.3 Linked Areas 169
- 15.8.2.4 Schedule 170
- 15.8.2.5 Setting/Unsetting 170
- Late Working Support 171
- Temporary Unset 172
- 15.8.2.6 All Okay 173
- 15.8.2.7 Reporting 173
- 15.8.2.8 RF Output 175
- 15.8.2.9 Area Triggers 176
- 15.8.3 Editing a door 177
- Door attributes 178
- Door timers 179
- 15.8.3.1 Door Interlock 180
- 15.8.4 Adding an area group 181
- 15.9.1 Editing an input 182
- 15.9.2 Editing an output 184
- 15.10 X-BUS 190
- 15.10.2 Expanders 195
- Linked Mode 197
- Flexible Mode 197
- 15.10.3 Door Controllers 200
- 15.10.4 Cable Map 202
- 15.10.5 Settings 202
- 15.11 Wireless 203
- Wireless 205
- 15.11.3 Configuring a WPA 206
- 15.11.3.1 Adding a WPA 207
- 15.11.3.2 Editing a WPA 209
- 15.12.1 Serial ports 209
- Configuring communications 210
- 15.12.1.3 Troubleshooting 214
- 15.12.2 Modems 214
- 15.12.2.1 PSTN modem 215
- 15.12.2.2 GSM modem 217
- 15.12.2.3 SMS test 218
- 15.12.2.4 SMS feature 219
- 15.12.2.6 SMS Commands 219
- 15.12.3 Ethernet 221
- 15.12.6 SPC Pro / SPC Safe 224
- SPC Safe 225
- 15.12.7.1 SIA codes 226
- 15.12.8 EDP Setup 229
- 15.12.9 Remote Maintenance 236
- 15.13.1 Calendars 236
- Week Types 237
- Exceptions 238
- 15.13.2 Triggers 239
- 15.13.3 Mapping Gates 241
- To edit a X-10 device 243
- 16.1 PSTN connection 245
- PSTN connection 246
- 16.2 GSM connection 247
- GSM connection 248
- Intruder alarm functionality 250
- Financial mode operation 250
- 17.4 Full and local alarms 251
- Use of common areas: 253
- 19 Audio/Video Verification 254
- 19.4 Viewing Video Images 257
- Audio/Video Verification 258
- Viewing Video Images 258
- 19.5 Configuring Video 259
- 20 Seismic Sensors 262
- Seismic Sensors 263
- Configuring Video 263
- 20.1 Seismic Sensor Testing 264
- Periodic Automatic Testing 265
- Automatic Test on Setting 265
- AREA NAME’ 266
- ZONE NAME’ 267
- 21 Appendix 268
- Appendix 269
- Zone Names 272
- Zone Types 272
- 21.7 SIA Codes 273
- 21.8 CID Codes 278
- 21.10 User PIN combinations 280
- No of digits 281
- 21.12.3 Engineer Access 282
- 21.12.4 Keypad User Logoff 282
- 21.15 Maintenance Smart PSU 283
- 21.16 Zone types 284
- 21.17 Zone attributes 286
- Hardware Requirements 293
- SPC43xx/SPC53xx/ SPC63xx is: 295
Powiązane produkty i podręczniki dla Klawiatury numeryczne Siemens SPCK421
(20 strony)
(49 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji