Siemens SINUMERIK 802D sl Instrukcja Operatora Pobierz pdf (Strona 111)

NCK alarms

06/2009 Overview of alarms

2-111

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

The macro definitions and cycle interfaces are also read in during the power-up procedure. If an error

occurs here, this is indicated by value = 4, or value = 5

6: Error creating 2 1/2 D protection zones during power up.

(Program) START:

Value

100: Error during synchronization preprocessing/main run

101: Error on selection of tool length compensation

102: Error on selection of transformation

103: Error on selection of synchronized spindle

104: Error on selection of work offset

Particularly when tool management is active, it is possible that a tool on the spindle or the toolholder

is disabled but still needs to be activated.

These tools are automatically activated on RESET. On START, machine data MD22562

$MC_TOOL_CHANGE_ERROR_MODE can be used to specify whether an alarm is to be generated

or an automatic bypass strategy selected.

If the parameter contains 3 values from 200 to 203, this means that an insufficient number of NC

blocks is available for NC block preparation on certain commands (ASUB start, overstore selection,

teach-in).

Remedy: Increase machine data MD28070 $MC_MM_NUM_BLOCKS_IN_PREP.

Reaction: Interpreter stop

Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Please inform the authorized personnel/service department.

If parameter %3= 0 -3:

If the alarm or alarms occur on RESET:

Check the settings of machine data MD20110 $MC_RESET_MODE_MASK,

MD20120 $MC_TOOL_RESET_VALUE, MD20121 $MC_TOOL_PRESEL_RESET_VALUE,

MD20122 $MC_TOOL_RESET_NAME (only if tool management is active),

MD20130 $MC_CUTTING_EDGE_RESET_VALUE, MD20132 $MC_SUMCORR_RESET_VALUE,

MD20126 $MC_TOOL_CARRIER_RESET_VALUE,

MD20150 $MC_GCODE_RESET_VALUES, MD20154 $MC_EXTERN_GCODE_RESET_VALUES,

MD20140 $MC_TRAFO_RESET_VALUE,

MD21330 $MC_COUPLE_RESET_MODE_1,

MD24002 $MC_CHBFRAME_RESET_MASK

If parameter %3= 100 - 104:

Check the setting of MD20112 $MC_START_MODE_MASK and the machine data specified under

'..._RESET_...'. If tool management is active, if necessary remove the tool stated in the associated

alarm from the toolholder/spindle and cancel the 'disabled' status.

If parameter %3= 4 or 5:

Check macro definitions in _N_DEF_DIR

Check cycle directories _N_CST_DIR and _N_CUS_DIR

If parameter %3= 6:

Alarm 18002 or 18003 was also issued. This alarm contains the number of the incorrectly defined pro-

tection zone and an identifier of what is incorrect about the protection zone. The system variables must

be appropriately corrected.

If Parameter %3= 200 bis 203:

Increase MD28070 $MC_MM_NUM_BLOCKS_IN_PREP.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

14711 [Channel %1: ] Transformation selection not possible as axis %2 not

available

Parameters: %1 = Channel number

%2 = Axis name, spindle number

Definitions: Based on the configuration of machine data MD20110 $MC_RESET_MODE_MASK and MD20140

$MC_TRAFO_RESET_VALUE, a transformation shall be selected by performing a reset or control

ramp-up. However, this is not possible as axis %2 required for this is not available. Possible reason:

The axis was occupied by another channel or the PLC.

Reaction: Interface signals are set.

1 2 ... 106 107 108 109 110 111 112 113 114 115 116 ... 339 340

Siemens SINUMERIK 802D sl Instrukcja Operatora Strona 111

Komentarze do niniejszej Instrukcji

Siemens SINUMERIK 802D sl Instrukcja Operatora Strona 111

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Siemens SINUMERIK 802D sl