Siemens SINUMERIK 802D sl Dokumentacja Pobierz pdf (Strona 221)

NCK alarms/ISO alarms

06/2007 Overview of alarms

2-221

SINUMERIK 802D sl, Diagnostics Manual, 06/2007Edition

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

20058 Channel %1 axis %2 revolutional feedrate: illegal feed source

Parameters: %1 = channel number

%2 = axis name, spindle number

Definitions: An axis/spindle is to be traversed at revolutional feedrate. The reference axis/spindle defined in SD

43300 ASSIGN_FEED_PER_REV_SOURCE refers to itself. The coupling created cannot be exe-

cuted.

Reaction: Alarm display.

Remedy: The spindle/axis from which the feed is to be derived refers to itself.

Program Con-

tinuation:

Alarm display showing cause of alarm disappears. No further operator action necessary.

20059 Channel %1 axis %2 already active due to %3

Parameters: %1 = Channel number

%2 = Axis name, spindle number

%3 = Cause

Definitions: The axis (machine axis, geometry axis or orientation axis) is to be traversed in operation mode "Auto-

matic&Jog" (see $MN_JOG_MODE_MASK) by using the direction keys or a handwheel. This is not

possible, as (see parameter 3):

1. the axis is active as a rotating spindle

2. the axis is a PLC axis

3. the axis is active as an asynchronous reciprocating axis

4. the axis is active as a command axis

5. the axis is active as a slave axis

6. a frame applies for a rotated coordinate system and an axis involved in the required JOG movement

of the geometry axis is not available for this

7. an axis container rotation is activated via NCU link

Note: This alarm identifies an axis not capable of JOG which received a JOG order. In this case, the

NCK will not proceed according to "Internal JOG".

Reaction: Alarm display.

Remedy: Wait for the axis to traverse or abort with distance-to-go delete or RESET.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

20060 Channel %1 axis %2 cannot be traversed as geometry axis

Parameters: %1 = channel number

%2 = axis name

Definitions: The axis is currently not in "Geometry axis" state. Therefore, it cannot be traversed in JOG mode as

a geometry axis.

If the abbreviation WCS (workpiece coordinate system) is displayed in the "Position" screen, then only

the geometry axes can be traversed by means of the direction keys! (MCS ... Machine coordinate sys-

tem; all machine axes can now be traversed by using the direction keys on the machine control panel).

Reaction: Alarm display.

Remedy: Check the operating steps to establish whether geometry axes really must be traversed, otherwise

switch over to the machine axes by activating the "WCS/MCS" key on the machine control panel.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

20061 Channel %1 axis %2 cannot be traversed as orientation axis

Parameters: %1 = Channel number

%2 = Axis name

Definitions: The axis is not an orientation axis and can therefore not be traversed as an orientation axis in JOG

mode.

Reaction: Alarm display.

Remedy: Register the axis as an orientation axis.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

1 2 ... 216 217 218 219 220 221 222 223 224 225 226 ... 391 392

Komentarze do niniejszej Instrukcji

Brak uwag

Siemens SINUMERIK 802D sl Dokumentacja Strona 221

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Siemens SINUMERIK 802D sl