Siemens SINUMERIK 802D sl Dokumentacja Pobierz pdf (Strona 333)

Profibus alarms

06/2007 Overview of alarms

2-333

SINUMERIK 802D sl, Diagnostics Manual, 06/2007 Edition

POSCTRL_CYCLE_DELA especially:

POSCTRL_CYCLE_DELAY must be larger for type 1. POSCTRL_CYCLE_DELAY must be smaller

for type 2.

If alarm-free operation cannot be achieved with any POSCTRL_CYCLE_DELAY setting,

SYSCLOCK_CYCLE_TIME must be increased.

If the error cannot be eliminated by this procedure, please make a note of the error text and contact

the control system manufacturer.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

380020 PROFIBUS DP: bus %3 SDB %4 error %1 source %2

Parameters: %1 = cause of error

%2 = SDB source

Definitions: Error in SDB for PROFIBUS DP configuration.

Error cause:

01=SDB not present in SDB source

02=SDB in SDB source too big.

03=SDB cannot be activated in SDB source.

SDB source:

00=Default SDB1 (selected by MD 11240 = 0 if no user SDB is loaded in the control system)

01=Standard SDB1 (selected by MD 11240 = 1)

02=Standard SDB2(selected by MD 11240 = 2)

...

100 = SDB located in supported memories (SRAM)

101 = User SDB located in file system

102 = SDB reloaded in SRAM during power-up

Reaction: Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Check MD 11240

If SDB source = 100: Reload user SDB in passive file system /_N_IBN_DIR/_N_SDB_BIN.

If SDB source = 101, check support accumulators.

If SDB source = 102: Follow the procedure described for troubleshooting alarm 380001.

If alarm 380021 is also signaled, please follow the instructions provided for this alarm.

If the error cannot be eliminated by this procedure, please make a note of the error text and contact

the control system manufacturer.

Program Con-

tinuation:

Switch control OFF - ON.

380021 Profibus-DP: default SDB-Type-2000 was loaded

Definitions: No user-specific SDB exists.

The default SDB was loaded during startup.

Without process peripherals, the NC is ready for a start-up.

The alarm is triggered the first time the NC is switched on or once if the SDB stored in the supported

RAM is lost.

Reaction: Alarm display.

Remedy: Produce user-specific SDB and load in the control or select and activate standard SDB using MD

11240 PROFIBUS_SDB_NUMBER.

Restart the NC.

If the error occurs the next time the NC is switched on, the SDB which was loaded contains an error

and must be created again.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

380022 PROFIBUS DP: configuration of DP master bus %1 has been changed

Parameters: %1 = number of the bus affected

Definitions: The PROFIBUS configuration on the DP master was changed during operation, e.g. by downloading

a new hardware configuration. Since it is possible that the cycle data has changed, operation cannot

be continued and a warm start is required.

Reaction: Channel not ready.

NC Start disable in this channel.

1 2 ... 328 329 330 331 332 333 334 335 336 337 338 ... 391 392

Komentarze do niniejszej Instrukcji

Brak uwag

Siemens SINUMERIK 802D sl Dokumentacja Strona 333

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Siemens SINUMERIK 802D sl