Siemens SINUMERIK 802D sl Dokumentacja Pobierz pdf (Strona 26)

Overview of alarms 06/2007

NCK alarms/ISO alarms

2-26

SINUMERIK 802D sl, Diagnostics Manual, 06/2007Edition

4114 Error in DP cycle of SDB-Type-2000

Parameters: %1 = String (new PLC cycle)

Definitions: The DP cycle in the SDB contains an error and cannot be set.

The default value of MD 10050 SYSCLOCK_CYCLE_TIME is set.

Reaction: Alarm display.

Remedy: Correct the SDB.

Program Con-

tinuation:

Switch control OFF - ON.

4115 Time ratio communication to Ipo changed to %1

Parameters: %1 = String (new PLC cycle time)

Definitions: The value of the machine data 10072 has been adapted. This can only occur, if the value of the

machine data is smaller than one and the time thus calculated is no multiple of the position control

cycle.

Reaction: Alarm display.

Remedy: The machine data $MN_COM_IPO_TIME_RATIO has been adapted. Please check to ensure that the

calculated value is correct.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

4150 Channel %1 invalid M function subprogram call configured

Parameters:

Definitions: In MD MD 10715 M_NO_FCT_CYCLE, an M function that is occupied by the system has been spec-

ified for the configuration of the subprogram call and cannot be replaced by a subprogram call (M0 to

M5, M17, M19, M30, M40 to M45, M70). When external language is active, M96 to M99 are also

blocked

Reaction: Mode group not ready.

Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: Configure an M function which is not used by the system (M0 to M5, M17, M19, M30, M40 to M45 and

M70) in MD 10715 M_NO_FCT_CYCLE.

Program Con-

tinuation:

Switch control OFF - ON.

4152 Illegal configuration of the 'Block display with absolute values' function

Definitions: The "Block display with absolute values" function has been illegally parameterized:

- An illegal block length has been set with MD 28400 MM_ABSBLOCK:

While ramping up, the machine data will be checked for the following value range:

0, 1, 128 to 512

- An invalid display range has been set with MD 28402 MM_ABSBLOCK_BUFFER_CONF[]. While

ramping up, the machine data will be checked for the following upper and lower limits:

0 <= $MC_MM_ABSBLOCK_BUFFER_CONF[0] <= 8

0 <= $MC_MM_ABSBLOCK_BUFFER_CONF[1] <= (MD 28060 MM_IPO_BUFFER_SIZE + MD

28070 MM_NUM_BLOCKS_IN_PREP).

Alarm 4152 is issued if the limits are violated.

Reaction: Mode group not ready.

Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: Configure block length/display range within the permissible limits.

Program Con-

tinuation:

Switch control OFF - ON.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 391 392

Siemens SINUMERIK 802D sl Dokumentacja Strona 26

Komentarze do niniejszej Instrukcji

Siemens SINUMERIK 802D sl Dokumentacja Strona 26

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Siemens SINUMERIK 802D sl